Follett C/E25HT400A/W Manuale Utente

Installation, Operation and Service Manual Following installation, please forward this manual to the appropriate operations person.00124446R02C/E25CT4

6. Temporarily remove rear access panel (Figs. 4 and 5) from rear of dispenser. 7. Loosen junction box mounting screws. Lift junction box and pow

Installing wall mount dispensers 1. Install supplied wall bracket with six 10 mm (3/8") diameter fasteners as shown in Fig. 7. Note: Three hol

8. Remove utility knock-out (Fig.4, 5F) from rear of dispenser and install supplied protective grommet. For dispensers using Satellite-fill icemake

Installing Satellite-fill icemakers (models C/E25CR400A/W, C/E50CR400A/W, C/E25HR400A/W, C/E50HR400A/W) 1. Install Satellite-fill icemaker following

14Installing top mount icemakers (models C/E25CT400A/W, C/E50CT400A/W, C/E25HT400A/W, C/E50HT400A/W) 1. On dispensers equipped with topmounted, wate

15capillary tube45°19mm(.75")Hand bend cap tubeend to approx. 45°as shownFig. 11 – Ice transport tube and bin thermostat capillary tube mounting

User informationHow the dispenser worksFollett’s 25 and 50 automatic load ice and water dispensers receive ice from Follett’s 181kg (400lb)/day icemak

Recommended weekly cleaning 1. Wash drain pan and grille with Solution A above. Rinse thoroughly. 2. Slowly pour solution of 237ml (8 oz) househo

WTRMMAIN POWERSWITCHBIN SIGNALSWITCHBIN SIGNAL FROM ICE MACHINE(230 V)ICE MACHINEPOWERWHITEWHITEWHITEWHITE4x4 JUNCTION BOXBLACKGREENBlue BLUEPURPLEBLU

How unit works — SensorSAFE modelsSensorSAFE models provide “touchless” ice and water dispensing. When a container is placed within the actuation zone

Follett CorporationEquipment Return PolicyFollett equipment may be returned for credit under the following conditions:1. The equipment is new and unu

20Dispenser troubleshootingBefore calling for service:• Check that there is ice in dispenser bin area • Check that all switches and circuit breaker

21ActionCheck LEDs on control board.Place cup under drop zone.LED Status PWR CLN ICE/WTR OFF OFF OFF ON ON OFF ON OFF OFF ON OFF ONSolutionC

22Lens/sensor troubleshooting 1. Turn dispenser power switch off. 2. Remove splash panel. 3. Disconnect wires from output terminal(s) (WTR, WM) o

Ice transport tube replacement models C/E25CT400A/W, C/E25HT400A/W, C/E50CT400A/W, C/E50HT400A/W Only use tubing supplied by Follett Corporation.!Dis

Ice transport tube replacement models C/E25FB400A/W, C/E50FB400A/W, C/E25CR400A/W, C/E50CR400A/W 1. Remove top and rear access panel from dispenser

well nutcapillary tuberubber grommetcontrol box assemblyice mounting hose bracketknurled screwhopper assemblycapillary tubebin thermostatcontrol box a

26Part # Description Reference502916 Cover, top front, 25 countertop (CT) & wall mount (HT) units 1502917 Cover, top front, 50 countertop (CT

Part # Description Reference502057 Fastener, dispense chute bracket 1502356 Tube, water station 2502681 Cover, dispense chute 3502359 Switch

Dispense chute and splash panel areas — SensorSAFE models1328Part # Description Reference502057 Fastener, dispense chute bracket 1502681 Cover, d

Part # Description Reference500514 Thermostat, bin level 1502209 Switch, dispenser power 2502209 Switch, icemaker bin signal 2502915 Control bo

3Before you beginSpecifications Field wiringInstallation Installing freestanding dispensers Installing countertop dispensers Installing wall mount

30Part # Description Reference501608 Baffle, ice 1501614 Wheel, dispense (includes drive bar, rotating agitator, threaded bar & rod) 2502821

31Part # Description Reference502598 Coil, chilled water (includes two 502599) 1502599 Fitting, water coil 2502600 Brackets, chilled water cani

00124446R0210/06801 Church Lane • PO Box D • Easton, PA 18044, USA(610) 252-7301 • Fax (610) 250-0696 • www.follettice.com

Welcome to FollettFollett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale

5Plumbing 25/50C with 25/50H with 25/50C with 25/50H with 25/50FB Satellite-fill Satellite-fill integral integral icemaker icema

6Model Electrical connection CurrentC25FB400A/W, C50FB400A/W cord provided 220V 60Hz, 6.5 ampE25FB400A/W, E50FB400A/W 230V 50Hz, 6.5 ampC25CT400A

Installation proceduresInstalling freestanding dispensers 1. Carefully tip dispenser back to expose underside and block up in place. 2. Remove leg

10. Remove front cover of base section by removing two screws at bottom corners of cover. Allow cover to drop approximately 10mm (3/8") and pul

Installing countertop dispensers 1. Position dispenser in desired location, mark dispenser outline on counter and remove dispenser. 2. Drill four